Retractable boxes under the bed do it yourself. Production of drawers with their own handsInformational construction site |

In modern apartments, not many of which can "boast" a large square, each square meter on the account. Special place in the furniture furniture is occupied by furniture. Its functionality can significantly save expensive square meters, which, as a rule, is always lacking.

Content

Single beds with linen boxes appeared relatively long. Such a piece of furniture allows you to most effectively use the space of the room. In niches or drawers, you can store bedding, clothing or other temporarily unnecessary things. It is worth noting that the cost of such models is much higher than ordinary, but thanks to their ergonomic, their popularity is growing every year.

How to make a drawer with your own hands for the finished bed

Bed for bed can be done with your own hands. If there is a certain tool and the initial skills of working with it, this task will not be complex. Use with benefit free space under the bed lying in two ways:

Make a lifting bed with a niche under it.
Make a roll-out or retractable boxes that will open before the bed or side.

The second option, of course, is preferable, although it assumes the presence of a "dead zone" at the extension area of \u200b\u200bthe box. At this place it will be impossible to put any item. However, it is much easier to use such a design and safer than to raise a heavy mattress. About how to make a bed with drawers with your own hands - further in the article.

This option is quite popular for those who buy factory furniture, but over time think about more efficient space. In this case, the retractable box is a separate design that is not part of the bed itself. The designs are nominated not on guides as built-in, but on their own wheels.

For the construction of such a box with mandatory parameters are:

Distance between the legs of the bed. In order for the box normally put forward and not clinging for the dimensions of the bed, its width should be slightly smaller than the distance between the legs. However, you should not make a box too narrow. When using it will be done, which makes it difficult to put forward. The gap between the drawer and the legs of 20 mm will be enough.
The height of the box should be 10-15 mm below the height from the bottom panel bed to the floor.
The depth of the drawer should be such that its front panel is hiding under the bed.
For storage of bed linen, so that it does not dust, a special case with lightning case is dressed on the surface of the box, which will be opened and closed if necessary.

For making drawer, you will need:

Plate laminated chipboard. Dimensions must match the size of the product. From it will be made bottom drawer. For this work, it is impossible to use fiberboard, as the bottom must be tough, because the drawer rollers will be attached to it.
Material for sides. An ideal option for the production of boxes of the box can be laminate, especially if this material remained after laying the flooring. With its relatively small thickness, it has excellent operational and strength characteristics.
Furniture fittings. For the construction of the drawer, the following fittings will be needed: rollers (minimum 4 pcs.), Steam furniture handles, furniture steel corners, self-tapping screws.
If the standard length of the laminated panel is not enough, it can be folded from two pieces into the lock, pre-lubricating the locks with the glue for wood.

It will be guaranteed from the tool:

Electrolovka.
Electric screwdriver.
Screwdriver.
Roulette, pencil Cornel.

Procedure for work:

The first step is to saw base box made of laminated chipboard. It should be done carefully so as not to damage the edge of the plate. If there is a ready tabletop required size (for example, the old table), you can use it.
Next, you need to prepare a side drawer. To connect this laminate strip using steel furniture parts. Since laminate - it is rather thin material, without corners to collect it together will not work. When assembling the sides of the box should be done so that the angles between the bars were strictly straight.
Self-tapping screws are screwed in using the screwdriver. It is very important to choose the fasteners so that when the assembly did not pass through. Use a drill, especially a steel chuck in such work impossible. It has a large inertia of rotation and thus can rotate the screw a few more times. In this case, the hole wall collapse and not be able to keep the screw from moving.
Before assembling the sides of the box you want to remove the locks of laminated panels. This is done very simply - using the jigsaw. In the area of \u200b\u200bthe castle is the smallest thickness of the laminate, so get rid of it is not difficult.
After the flange is assembled with the inner side of the bottom of her screwed seating area in increments of no more than 120-160 mm. This is done all around. It is with them a flange is attached to the bottom of the box.
After the corners are screwed can be fastened to the bottom side. This is done using the same screws. If done correctly, at the joints should be no gap.
The next step is to install the rollers. You can buy them at any store furniture sets. They are installed at the corners of the bottom. If they are set close to the center of the box is unstable.
The final touch in the assembly will be the installation of the drawer handles. For easier rolling out the last two handles placed.
After the end of the installation the product is rolled under the bed. For proper operation of such a box can be quite long.

Manufacture of drawers bed with his hands

To make a bed with drawers with your own hands, you must work hard.

bed design will consist of several main components:

Headboard.
footboard
Boxes for drawers
supporting grid
Boxes.

Procedure for work:

The first thing is made by the headboard bed double with storage boxes. Since it, as well as trading, will be the main supporting structures, their framework is made from a bar with a cross section of 100x100 mm. The height of the headboard will be equal to 1400 mm, squatting - 600 mm. The width of both parts should be the same and will be 160 cm. Such width is quite sufficient for a double bed. To make these details more attractive between the bars, you can insert a sheet of plywood. For this, they make special grooves.
For the assembly of the head and the finishes are used for carpentry and nails.
After the completion of these parts, it is started with boxes. The length of the three-section box will be 2000 mm, the width is 400 mm, the height is 350 mm. The boxes are collected from plywood with a thickness of 20 mm, the width of each section under the box is 650 mm. The assembly of boxes is made using nails and joinery glue. Be sure to strengthen the walls of the box with steel furniture corners.
After completing the work, the rear wall of the box is closed with a leaf of laminated fiberboard. The second box is also manufactured.
Then the boxes are attached to the head of the head and graduate. It is important that the fastening places are on the bars. Confirmates are used as fasteners. Now the design is more like a bed. However, there was a space between the boxes to which the mattress cannot be laid (it will simply fall). In order to prevent this, a supporting grid is installed between the boxes. On each of the boxes by 20 mm below the top edge over the entire length, the timber is mounted with a cross section of 20x20 mm. In the ends, it is fixed to the head of the head and graduate. Additional legs are attached to the brushes and boxes on both sides in the middle of the bed. They are needed to reduce the load on the box with drawers and on the head of the head of the head and flying. Additional legs are made of a bar with a cross section of 20 mm x 20 mm.
Next, a short strip of the same material is installed on top of the fixed bars. Step installation step - no more than 100 mm. They are attached with nails or screws. If the entire installation process is performed correctly, the bed surface will be at one level.
Now you can proceed to the manufacture of drawers under the bed with your own hands. For such a design of the bed, they will need 6 pieces (3 on each side). The walls of the boxes are made of plywood with a thickness of 20 mm, and the bottom of the leaf is 6 mm thick. The size of each box is 630 mm x 350 mm. The walls are connected to each other with glue and nails. From the front side of each box, the front decorative lid with moldings is installed. Moldings can be made independently or buy ready-made in the store.
The finished box is installed on special accessories. Guides for drawers should be installed at a distance of at least 25 mm from the edge of the niche. In this case, the decorative panel with moldings will be flush, which will make the bed more attractive. So that the boxes easily put forward, the handles are attached to them. Especially beautiful will look for the handles "under the old".
The last stroke will be the coating of the entire design of the bed with a protective coating, which will prevent wood damage. To begin with, the entire surface of the bed is opened by a verse. She will give the tree an excellent look, emphasizing his texture. The procedure is repeated twice. Then two layers of colorless varnish are applied. It will be a protective layer so as not to damage the wood. The only thing remains to put the mattress on the bed.