Everyone knows the statement that "the theater begins with hangers." It is worth saying that not only in public institutions the hanger is playing an important role, but also in apartments and houses. After all, the absence of this important subject of the interior can cause disorder in the hallway. Today there are many all kinds of hangers of different shapes and designs, but it will be completely easy to do with its own forces from the primary materials. How to do it - tell me further.
Content
Selection of product design
For the manufacture of clothes hangers typically use wood. But not every material is suitable for this. It is necessary to choose the most leaking and durable wood. If the material does not succeed as it should be dry, then after a while it can lose its shape. Of all the wood breeds for hangers, it is recommended to give preference to pine. This material is good because it is easy to handle and has a small weight. If you decide to use an array of oak, then you should consider that it is more difficult to handle and is heavier. Parts of wood hangers typically combine with glue. It is similar to some important requirements. By the way, the glue in the presence of unreasonable wood can lose its adhesion, due to the selection of moisture with the material.
A very important role is played by the choice of hanger shape. It should be borne in mind that for this subject of the interior it is necessary to at least three supports, the length of which directly depends on the height of the product. Thus, it turns out that the higher the hanger, the more massive and more of it should be supports. Often this product is intended not only for the outerwear, but also for trousers, to keep all the clothes in one place. For this purpose, the width of the hanger is usually done more than usual. Thus, a lot of different clothes can fit here.
When you were determined with the hanger model, you should draw a scheme in which exact dimensions of the future product will be indicated. Moreover, it is advisable to describe the size of the even the most slightest parts. This will have to be likewise during the manufacture of the product. When the scheme is ready, you can start mounting the hanger floor for clothes wooden.
Clothes rack outdoor with their own hands
For the manufacture of the product requires:
- saw,
- knife,
- drill,
- stack
- chisel.
Necessary materials:
- bars of the desired size
- boards
- wood glue
- self-tapping screw
- artwork for processing the product,
- varnish.
When all this is, you can proceed to work. It is advisable to decide in advance with a tint of the future product. In general, light wood can be painted almost in any tone. To do this, it is enough to apply a veil until the surface of the hanger is the desired shade. When coating, a verse or varnish should be put under the product some substrate. Otherwise, the drops can accidentally get to the floor. Laccue should be used only after complete drying of the veil. In general, with a varnish due to a strong smell, it is best to work in a room that is well ventilated or, in general, outdoors. After opening the varnish, the product should be wiped with a rag moistened in a weak vinegar solution.
Consider the order of work:
- First you need to prepare wood. In particular, the trunk of the tree is cleaned of the bark and coarse bitch. Corre in no way should be left, no matter how much it wanted to give the product a more natural look. After all, if you leave it, it will gradually turn, thereby creating an additional reason for cleaning the room. In addition, the bark is often the habitat of small insects.
- Corre can be removed using an ax or knife. After that, you should walk several times on the wood first coarse, and then shallow emery paper. The surface in the end should become smooth, at least in order for the knots not clinging clothes.
- After that, it is necessary to make the basis of the product. It is worth saying that all elements of hangers (legs and tripod) are desirable to make one whole. It is not worth starting from the cross. Otherwise, if it is then to attach the hanger itself to it, the design can overcome over time. It is necessary to follow the following rule - the lower edge of the tripod must be performed on the same plane with the legs of the legs.
- After that, you can proceed to measure the diameter of the barrel. Sizes dropped will be needed to select a suitable width bar. If the bar is wider than necessary, then you can cut it with a hacksaw along to the desired size.
- Typically, the heating height is about 1.7 m. For the product of such a height of the cross should have departures of about 30-32 cm. Therefore, a pair of bars 65 cm long will be needed. They will need to be cut in half to make four billets about 30-32 cm long.
- The most difficult thing is to attach the legs to the circular barrel. If you just attach bars, the design will be unstable, and after the first trip, most likely falls apart. It is more correct to put a tripod on the floor and put the blanks of the legs to it. To connect them, you will need to make triangular wooden inserts. Then they are attached to the bars using self-tapping screws.
- To strengthen the product in places of attachment of the triangular elements to the legs and the trunk, you need to drill a hole with a diameter of several millimeters less than the fastener diameter. It will later need to pour glue. Only after that you can turn the screws. Sometimes to impart the stability of the hole design, except for glue, are also filled with pieces of rubber.
- To give the finished hanger functionality, you should add hooks for outerwear to it. They can be made at some distance from the barrel. Here one important rule should be observed. So that the design does not fall, the center of gravity hanged on the clothes hanger should not be outside the cross.
- Hooks can be used both homemade and decorative. In any case, they cannot be attached directly to the tripod, because the hanger outdoor for clothes is quickly wear out and will be in disrepair. It can be done like this: take the bars and cut down the square with a side of several more than the diameter of the barrel. Initially, the hooks are attached to this square of the tree, and then to the product itself. Thus, they will be securely fixed, and at the same time will not contact the product with the "body", which, thanks to such a device, will last longer. This is especially useful for wardrobe hangers, which are used quite often.
You can decide what hooks to use are decorative or homemade. However, if you make them yourself out of the wire, they will not have a very attractive look. Therefore, it is still better to give preference to decorative hooks purchased in the store. They are usually attached to a tree for a couple of screws. If there are necessary skills, you can cut the holes of the square shape using the chisel, where you should then "hide" hooks. It will look better than a simple attitude on the self-tapping screw. When the hooks are in place, you need to connect a square wooden insert with the upper part of the product using multiple screws.
As for the hanger itself, it can be painted or covered with varnish. Chief Choose to your taste, but it is better to pick up the premises finishing style, where the wooden hanger is standing outdoor for the hallway. The paint or varnish layer is applied at least two times.
The base for the floor-haired wooden hanger should be sufficiently heavy and stable. As it, you can adapt the bottom from the lamp, the oscillation of the outdoor fan or buy a stand for the New Year tree.
Costume Hanger Outdoor Wooden
The above-described hanger is not suitable for men's suits. Therefore, it makes a slightly different design for them. The main material is similar to wood. To assemble such a hanger, you must first measure and cut the blanks, according to the specified dimensions. Then they are carefully processed and polished. After that, fasteners are fastened in the right places.
Next, according to the scheme, the product itself is assembled and its finishing finish is performed. It will remain to attach to the base of rubber or wheels. A little more about the assembly of such a hanger: first vertical racks are screwed to the base using 4 large screws. Then the plank is inserted between these supports and with the help of small screws. Next, the holder for trousers is inserted into the holes of the vertical racks. To securely fix it, the kiyanka will come in handy. After that, the design is screwed to vertical racks using four screws. Then the shoulders are screwed. The costume rack is ready for use.
How to make a wall hanger
The basis of such a hanger is a shield on which hooks placed. It can be done both solid and lattice. For the latter, you will need less material, and besides it is easier. To build such a shield take a couple of bars and attach in parallel to each other by means of a dowel. After that, the vertical strips of about 8 cm wide are nailed to them, and the hooks are attached to the boards.
The dimensions of such hangers can be different and mainly depend on the wall dimensions and the entire premises. If you wish, it is possible to place it beautifully: cover with varnish, paint or caught with a self-tier film. In any case, do not forget how to handle ends and edges, so that there are no roughness left. If there is a desire, you can do at the top of the hangers with the help of metal corners the shelf in the form of a boards of about 25 cm wide, where the caps will be stored. If the hanger is manufactured in the entire height of the wall, then in the bottom, it is usually equipped with a shelf for shoes. It is advisable to set the bottom of 5 × 5 from the bottom of the bars with a size of 5 × 5, which will support this shelf.
Wooden floor hangers: Photo
