Adjusting the accessories of plastic doors

Metal plastic doors are very popular and not only as balcony. They have long appeared in our bedrooms and halls. And nothing surprising - they are beautiful, lungs, easy to care. For a long service life, there is little that the metal-plastic design itself is high-quality, the corresponding fittings for plastic doors are needed.

What applies to fittings?

Furnitura is:

• locks;
• loops;
• devices, at the expense of which moves;
• connections.

Loop

The plastic door is though easier than the wooden one, but it can still be somewhat saved if such a type of accessories like a loop will not be adjusted correctly. In addition, the door is fixed with the hinge. So this item is very important and must meet the following requests:

1. It is good to perform your function with a load not exceeding 120 kg;
2. They should provide for the likelihood of coordination of such parameters as:

• height;
• clamp;
• horizontal offset.

High-strength alloys loops consist of:

• The housing, which in turn includes two parts:
  • A frame that has a built-in pin by which the mount is carried out;
  • Clause with a special tab.
• junction bushings;
• fasteners.

Usually, the doors of PVC have such a number of loops that corresponds to the conditions where it works.

Stopor.

• Ensure the fixation of the door in the desired position;
• doors with a stopper will save the fingers of children from pinching.

Closers

• Provide smooth door movement. Thanks to the closer, it does not slap and never gives away your fingers;
• protect the door handle and walls from damage, as they limit the amplitude when opening the door;
• increase the service life of the loop.

Closers on plastic doors, depending on the type of installation, are:

1. Top;
2. Lower;
3. Hidden.

Represents:

• spring, placed in the body filled with special oil;
• it has valves, with which the speed is adjusted with which the door closes.

Pens

This element of accessories for plastic doors is an integral part of them. All existing handles can be divided according to the following features:

• according to the functions that they can perform and this is 2 types:
  • stationary;
  • movable. They are also called faleva.
• by type of installation:
  • mortise;
  • overhead.
• depending on how the opening occurs:
  • whether from pressure;
  • whether from turning the handle.

Castles are inserted into metal plastic doors:

• mechanical;
• electromechanical.

All of them can be a lot or dispatch.

Adjusting the accessories of plastic doors

If you notice that something is wrong with your new plastic door, and it is still on guarantees, it is better not touching anything, to invite a specialist of the company that installed them. But, if this is not your case, since the door was installed independently or the warranty period managed to go through, then it will have to go to the adjustment of the fittings.

Tool

To adjust accessories for plastic door you need to have:

• two screwdrivers: one flat, other cruciform;
• set consisting of hexagon keys: 2.2-5 mm;
• pliers.

Most often, problems arise with a balcony door.

Adjusting accessories for balcony plastic doors

The balcony door, as well as the windows, is responsible for saving the heat in the apartment, so if the fittings are poorly adjusted, then this function will not be performed. To begin, the most reasonable thing, you need to establish the cause of the poor functioning of the door leading to the balcony. We will do it:

• first, check the state of the seal at the open door;
• we study, in what places in the sealing material, traces of squeezing are visible, and they will be on the side where the door has shifted;
• proof of the fact that you are not in vain suspect the presence of a shrinkage, is the bad job of the handle. Pay attention to how it works. If it is necessary to apply additional effort to its turn, and the knob is still not completely rotated, the tongue cannot match the groove, then this indicates a shrinkage.

Put the door to normal

Suppose there is a phenomenon: the door when opening or closing the threshold clings. There is a sagging under the influence of the glass unit. Even if a glass of 4 mm thick is involved in the glazing, and double-chamber double-glazed, then this is a decent weight, and if you, reinsulating not 4, and 6m mm, then the door will definitely offer. What to do? Of course, act:

• Open the door;
• we remove the decorative plug if it is;
• we take the key hexagonated 4 mm and adjust the upper loop, pulling up the screw;
• we restore the normal vertical door. At the same time, the screw turn clockwise;
• close the door.

There is another option:

• go to the bottom loop and release it from the decorative cap. Upper screw will be available for adjustment;
• adjust the screw at the top cover of the loop. Movement the same: climbing hours;
• perform checking the door stroke.

Note: In some types of door fittings, screws by which adjustment is performed not hexagon, but a star, so the key need appropriate.

If a battery is located next to the balcony door, then under the influence of constant heating, it can get a side offset horizontally. The same will be observed at some mechanical deformation of the door. Work in this case will be with the side screw:

• arming the key and twist the side adjustment screw;
• the sash will go towards the bottom loop;
• if this action has not given a positive result, we repeat the procedure from the top loop.

On the need to adjust the door adjustment density to the frame, says the fact that draft is clearly felt. Actions:

• it is necessary to regulate the Eccentric Treasures located on the canvas itself;
• using the key, rotate the eccentrics until the normal clamp is provided.

Wherein:

• if the Tsazpa takes a perpendicular position in relation to the profile, the door fit will be the greatest;
• position of the pin parallel profile - the smallest fit.

Note: adjust the clamp need twice: before the onset of the cold and spring. And: in winter, clamp is more dense, in warm time - weaker. If you rotate the adjustable key on the hourly, the clamp will be enhanced, counterclockwise - weaken. With a strong fit, the seal flashes faster.

Repair knob

This type of accessories for balcony plastic doors, as the handle is repaired and is simply adjustable. The most unpleasant thing that can happen to it - breaking down.

• Screws on the handle are usually closed with decorative plastic caps. They must be removed;
• we take a screwdriver and screw the screws, eliminating the backlash;
• if it did not eliminate the malfunction, inspect the handle carefully: it is possible for its body cracked. It will no longer help here, except to buy a new handle.

In case you really need to replace the handle, then:

• put the handle horizontally;
• unscrew fasteners;
• a new handle put on the place too.

It will not hurt to remember: the door must be shifted to the side opposite from the place where the sash constantly presses the seal.

Better accessories for PVC doors

In order for how less often I had to use your knowledge of the adjusting accessories of plastic doors, you need to choose products from well-known and reliable manufacturers. Here is the German company Roto, producing rotary-folding accessories of Roto NT, for example.

Her features

• The special environmentally friendly coating of Rotosil Nano is applied - very resistant to corrosion;
• the presence of the guide on which the mechanisms move;
• no additional security measures are needed, since Roto NT initially has the WK2 anti-svilness class.;
• there is a discovering lock, which makes it possible to hold the door in the open state. It will not even be able to close it;
• thanks to the microcirculation mechanism, the door sash can be folded.

Other

In addition to Roto, high-quality fittings are produced by such firms that are also in Germany as:

• G-U (Gretsch-Unitas GmbH);
• AUBI;
• Winkhaus;
• Siegenia;
• Maco.

Accessories from Gretsch-Unitas GmbH allows you to hermetically close the door, and again:

• in the upper loops there is a place for mounting the seal. It stacked smoothly and not shifted;
• the structure of the lower loops includes a screw sleeve, which provides the density of presidation to 0.15 cm.

Winkhaus, with headquarters in Germany, has its own branch and in Poland is "Winkhouse Ros". Products are different:

• ease of adjustment;
• adjustment of the clamp is performed throughout the perimeter manually using an eccentric roller;
• furnitura Winkhaus is certified in Russia and meets the Gostas:

1. 30777-2001;
2. 538-88.