Step by step instructions for assembling the cabinet coupe do it yourself

The wardrobe is a universal piece of furniture that allows you to streamline space and save a lot of place in the apartment. The process of assembling the cabinet coupe, quite complicated and without knowing some features of design and technological features not to do. Masters - furniture makers, have skills in the assembly of cabinets coupe, and the price is taken for the work not small.

Having step-by-step instructions for assembling the cabinet coupe and the scheme of its design, you can take up such work yourself. Preview the video about how the cabinet compartment is built.

Selecting a place and measurement room for installing a wardrobe

1. All furniture is made with perfectly straight corners, which you can not say about the floors and walls in our apartments. Therefore, armed with a plumb, a carbon, roulette and water level (water level), move, alleged installation locations of the cabinet coupe and select if not perfect, then at least close to ideal place.
2. Apply measurements on paper, making a small planner. Distances between the walls measure both below and at the top level. Visually inconspicuous building flaws, can manifest themselves when mounting the cabinet coupe and spoil all the work.

Step by step instructions for assembling cabinet coupe

Installation of the base

1. Works on the assembly of cabinets with their own hands begin with the installation of the base. Couple wardrobe - on low adjustable legs is convenient because the ideal horizontal plane of the base can be obtained by calibrating the screw controls on the legs.
2. The cross-cutting design of the legs allows you to adjust the bottom without much effort. The lack of such a bottom is a gap of about 25 mm, in which garbage can fall and dust.
3. Higher adjustable supports are covered with a decorative panel bar. It gives a more aesthetic look, but its installation makes sense at an ideally smooth floor surface.

Cabinet features and ribs

1. Confirming the lateral walls by configmatics, pay attention to the ribs. It is from them that depends the sustainability of the entire structure. An important point is the rear wall. Experienced masters of collectors are fixed with screws, and not nail.
2. The reason for the swinging of cabinets of the coupe, in the absence or improper installation of rigidity ribs. Their role is performed by transverse screeds in a bundle with the back wall of the waln sheets.
3. At the same time installed on the configmatics vertical simpleness and the roof of the cabinet coupe.
4. The scheme shows that when assembling cabinets, transverse screeds are attached to confirmates in each section separately and at different levels. This is necessary to provide appropriate stiffness over the entire height of the cabinet. In the central part there is one solid unifying screed.

Installation of shelves based on the axial line of the frame

1. As a rule, the installation of the shelves does not cause great difficulties during self-assembly of the cabinet coupe. Often they are located in separate sections at different levels.
2. With the axial location of the shelves, the angular furniture screed is put. It connects the vertical intermediate wall and the horizontal plane of the shelf.
3. For symmetrical fixation, angular screeds are added on both sides of the central axis of the fastening.
4. There is a different method of fastening the shelves on the central simple cabinet compartment - the "helicopter". This is not a completely standard attachment method, which consists in attaching one shelf to the confirmation in the center, tugging the shelf along the 90 ° axis, the adjacent shelf is attached to two confirm. The shelf is then returning to its original position and is enhanced by furniture tightening corners.

Assembly and installation of door cabinet coupe

1. Installation and hanging the cabinet doors are the final and most important stages of installation. The facade, the facial part sets a common visual picture for cabinets of the coupe.
2. Mirrors are pasted on the front part of the door leaf. For stickers, the film type "Oracale" is used along the entire plane of the mirror and in case the mirror breaks down, it will not allow fragments to fly out.
3. Horizontal profiles are installed. In the case of a tight entry of the profile in the groove, you can neatly sweep in the image.
4. A similar process is done with vertical profiles, and handles are installed.
5. Next, the rollers are installed, and the entire design is fastened with protracted furniture screws.
6. At the top of the doors, with the help of assembly screws, a horizontal and vertical door profile is collected and a roller is installed.
7. The lower part is going even easier. A roller is installed in the groove intended for it and fixed by self-draws.
8. In the upper part of the wardrobe opening, a guide rail is installed. It is attached strictly flush with bulkheads.
9. The bottom rail is somewhat recessed into the depths of the cabinet. Check the installation of the vertical and horizontal control measurements using Waterpas.
10. The last stroke will be the installation of the stopper and fixation of the cabinet with a compartment to the walls. In the upper parts of the cabinet, metal mounts are mounted with self-assembly and fix the design on the wall.

The sequence of collecting cabinets coupe is approximately the same for all types of this type of furniture. Assembling the corner cabinet Coupe does not differ from the assembly of the built-in wardrobe. Such cabinets are more stable due to the design of the base and additional supports on the walls. Instructions for their assembly are widely represented in the photo on the Internet.