It is possible to equip furniture from drywall for any room in the apartment. As a rule, stationary, built-in wardrobes, penalties and racks of various purposes are made from drywall. This inconvenience is completely compensated by the low cost of materials and ease of installation. To fit the furniture under the desired size, make and mounted independently can anyone.
Content
A positive moment of such furniture is an opportunity to implement your most bold design fantasies. Plasterboard can be given any of the most unusual shape, a large palette of pigment dyes allows you to paint the furniture in the corresponding interior color, and if you wish or need, it is easy to repaint in another.
The surface of kitchen furniture made of drywall can be saved duplex under painting or embossed washable vinyl wallpaper. Depending on the design plan, self-adhesive polychlorvinyl film and other finishing materials are used.
Drawings for plasterboard furniture
First you need to make a drawing of plasterboard furniture, photos and detailed instructions can be found on the Internet. The project can be ordered from masters or based on measurements, to independently draw on paper.
- Having determined the place for future furniture from drywall, make measurements with a tape measure and with the help of Waterpas, determine the correspondence of horizontal and vertical planes. Carpentry Check that direct corners are correct at several points of docking of the floor and walls. Spend at least three measurements vertically in the angular joints of the walls and output the deviation dedusions. Builders do not always adhere to strict parameters, and the possible discrepancies of the walls must be taken into account when designing furniture from drywall. Visually invisible builders' flaws can create significant problems if it is strictly in direct corners without taking into account such deviations.
- Sketch a pencil plan on paper, try to portray furniture in a three-dimensional plane - general view, side view and front part. The drawing indicating the size will help you make furniture from plasterboard with your own hands and calculate the required amount of materials.
Montage Framework Furniture from Gypsum Kitchen
Inspect the kitchen space and determine the location of the new plasterboard furniture. If there are niches in the kitchen - you can successfully use them. At your request, in the kitchen you can build separate elements of kitchen furniture - the couch, pencils, lockers - buffets or make a full kitchen corner.
- Start work with marking on the floor and walls, apply chalk with a long level rack of the line for the fastening of profile planks for plasterboard. Select a profile for guides and racks with a thickness of galvanized metal 3-4 mm. It will also be necessary for a wooden bar of the appropriate size, to fill the "P" - shaped profile. The bar must be well succeeded, since it may later twist. Choose waterproof drywall - 6.5 to 12.5 mm thick, it is most suitable for the kitchen atmosphere.
- Mount the profile to the walls and sex by self-draws and plastic dowels. In places contact profiles with floors and walls, a shock-absorbing gasket is attached, which quicpens likely vibrations of the building. Between themselves, the guide and rack profile are bonded by small screws "clouds". For arched and smooth bends, sideways of galvanized profiles with scissors for metal are trimmed. The step of the outbreak for non-standard configuration, depending on the degree of bending, ranges from 0.5 cm to 5 cm. Sometimes it is necessary to trim the protruding angles in the form of a trapezium.
- Horizontal guides for shelves, where you plan to arrange hypers or household appliances - for example: stacks of ceramic dishes, TV or microwave oven, it is desirable to strengthen the profile of a thicker metal, and be sure to insert a wooden timber in the middle.
Features of putty kitchen furniture from drywall
Basic surface must be prepared. Corners and joints are polished by sandpaper or special mesh grater. Survegencies are trimmed with a mounting knife for plasterboard.
- For internal and outer angular joints, a plastic or metal perforated corner can be applied. There is a flexible corner for arched or non-standard curved angles. Perforated corners are sled to putty. Fastening places, recessed by 1 - 2 mm in plasterboard are treated with anti-corrosion primer and rub in putty. The direct joints of the plasterboard canvas are strengthened by the self-adhesive reinforcing PVC ribbon.
- Before putting down, stroke and ground surface, cover the universal primer. Soil and putty are desirable to purchase one manufacturer's company. Dry putty waterproof water to the consistency of thick sour cream or purchased ready-made liquid putty. For alignment and bases, a layer of 2 - 3 mm starting putty is applied. A small spatula, a width of 8 - 10 cm superimposes on the edge of a wide spatula, a width of 25 cm and smoothly applied to the base surface of kitchen furniture from drywall, and then smoothed.
- After drying, the surface is sliced, it is applied with a layer of 1 - 2 mm of finishing putty and left until final graze. Finally, the surface is polished especially carefully. Circular motions, fine-grained abrasive material on a wide grater. The surface is ground deep penetrating universal primer and paint in suitable color, water-mounted paint.
Design solutions for decoration kitchen furniture Plasterboard
Drywall finishing materials for a lot. On the surface can be pasted wallpaper or self-adhesive PVC film, natural cork or ceramic tile. It all depends on the features of the kitchen design of the drywall.
Latex painted walls
Painting - the most simple and easy way to the final finishing of kitchen furniture made of plasterboard. The surface is coated with latex, brush or roller. Desired tone is achieved by adding pigment dyes. It should be noted that the drying saturation of colors is weakening, and eventually, under the influence of sunlight may fade altogether. Paint plasterboard furniture at least twice. The first coating latex paint, after drying will show the degree of color saturation. The second layer can lighten or vice versa, to saturate the color scheme and achieve the desired result.
Wallpapering on a plaster base of kitchen furniture
Side wall cupboards plasterboard can wallpapered to match or combined with the walls. Wallpaper paste, as well as on the wall. Kitchen fit tight washable wallpaper. Duplex wall paintable and have a waterproof sunscreen coating. As a rule, they have an embossed pattern or picture. Good fit vinyl wallpaper bilayer that mimic wood, burlap, ceramic tile, etc. Vinyl -. Sturdy enough intended for washing the material, it almost does not fade and is well suited for the kitchen.
Front doors for kitchen cabinets made of plasterboard
In the kitchen, just need to have cupboards with doors. Some shelves and niches can be closed by glass doors, the other - the facades of moisture-resistant MDF or wood. In the stores of furniture accessories offers a variety of fronts and mounting hardware for them. Beautiful pens always catch the eye and set a certain tone interior.
Lighting fixtures for kitchen furniture
Local lighting in the kitchen is very convenient and practical. Built in kitchen drywall furniture Spotlights perform a double function. They will be a harmonious element of the interior and functionally illuminate the zone necessary for the operation, while saving electricity. The location of the lamps is thought out in advance, and the installation and installation is made at the time of the construction of the frame and fastening of the plasterboard.
