Kitchen corner sofa. Step-by-step manual instructions

Often the kitchen is not only a place to eat, but also a pleasant pastime. Equipment of a comfortable and cozy corner will help the kitchen corner sofa. It will not always be the right solution to the problem to buy a sofa kitchen corner. It can be made it with your own hands, spending at least effort and funds. The result is reliable, original and created in accordance with the desired size kitchen sofa.

Often in factory kitchen corner sofas prices, color, sizes, quality or functional parameters do not satisfy the buyer. For a small or non-standard cuisine, it is easier and cheaper to make an angular sofa independently. Kitchen corner sofas photos that can be found on the Internet will prompt you model and design.

Tools and materials for the manufacture of angular kitchen sofa

For work, materials you can buy in the nearest construction store are required. Small skills in wood processing and minimal set of tools.

Sofa manufacturing tools

1. Electric jigsaw, planer, screwdriver, drill and grinding machine.
2. Hacksaw, pliers, hammer, roulette, chisel, carpentry corner, construction stapler.

Materials for the corner kitchen sofa

1. Brew with a cross section of 40x40 mm about 1350 mm.
2. Bar 24x25 mm - 3650 mm.
3. Bar 15x15 mm - 3000 mm.
4. Board 20x40 mm -1000 mm, Sosna, beech or birch suit.
5. Plywood 8 - 10 mm thick for the bottom and side walls - 2 sheets.
6. Fiberboard - used for the rear wall - 1 sheet. The method is given approximate, and more accurate is calculated according to the drawing.
7. Furnace foam rubber from 5 cm thick, high density and elasticity or synthesis.
8. Upholstery Material: Leather, Baratic, Nubuk, Tapestry, Microfiber, Velor, etc. Pay attention to the upholstery practicality. The coating should be easily cleaned and to be resistant to sanitation chemicals.
9. Consumables - screws (4x80, 4x60, 4x20 mm), confirmates, bent, loops, legs, bolts with washers (6 - 8 mm), etc.

A reliable factory mechanism will be required, if you want to make a kitchen folding corner sofa.

Stepped framework for an angular sofa

First of all, a drawing is drawn up with an indication of accurate sizes and dimensions. Based on the drawing makes the calculation of the necessary materials. The workpiece is shred and grind before marking and sawing. This will allow you to observe the accuracy of the size when fitting the sofa parts. Approximate corner sofa dimensions can be taken as a basis:

• maximum height - 855 mm;
• sofa length - 1200x900 mm;
• corner insert - 450x450 mm.

1. By and large, the design of the kitchen corner sofa does not make up big problems. The main carrier part is the sidewalls that carry the bulk. They are made from a solid sheet of thick plywood or a cohesive joinery. The markup is applied with a marker or pencil and is cut out with an electroll.
2. Collect 40x40 mm from a bar with two frames for long and short sofas. Frames are made in the form of parallelepipeds and are attached to the side planes. Corner connections are roasted on the thorn and mustache, then sit on glue. Fliced \u200b\u200bL and T - the shapes are set strictly at 90 °.
3. The angular compounds can be end-to-pass in Polbrus, with a single spike or two - three spikes, through or hidden in tight. For the strength of the connection is strengthened with a metal corner on self-drawing or brazers. The frame is collected in the complex with the back and screws to the sidewalls.
4. Having obtained the base of the angular kitchen sofa, the seat covers are collected. They can be solid for a long and short sofa or divided into sections. Rectangular seat frames are assembled from the bar 25x25 mm and is sewn 10 mm plywood. The finished seats are siny, covered with a veil and varnish, are glued to the foam plane and tighten the upholstered material. A piano loop will be screwed to the long side of the seats. Installation and installation of folding covers - seats are carried out at the final stage of work.
5. The smallest angular module is assembled in the same way. A frame of a triangular profile with sides of 90 ° and 45 ° is manufactured from the bar (40x40 mm). The module is hijacked by plywood or laminated fiberboard.

Build an angular sofa modules for kitchen

The collected blocks of two sofas and the corner module are thoroughly open. Places of chipsets or other damage arises during operation are embarrassed by a putty for wood. Wooden elements that will not be covered with an upholstery - covered with a verse and varnish. Laccular Corner Corner Corner for the kitchen is opened at least three times.

1. The delight details are put on small legs and rally. The legs can be purchased at the store furniture accessories, and they are attached screws to the reference parts of the sofa frame. It is necessary for at least eight legs for the entire corner sofa.
2. The structural elements are exhibited and by adjusting the height of the legs. The correct installation is checked by Waterpas. In the marked places, holes for fastening bolts with a diameter of 6 or 8 mm are drilled. Washers under bolts are purchased with a wide field. For each fastening bolt, you will need two washers. One washer is placed under the head of the bolt, and the second is under the nut.
3. By installing fastening bolts, take care of free access to them. After some time, the bolts will burn wood, and they will need to tighten. When permuting, moving or for thorough cleaning, the sofa disassembled is also required.

Upholstery and Corner Sofa Decoration for Kitchen

The upholstery for an angular kitchen sofa is selected taking into account its operation in the immediate vicinity of the kitchen plate and washing. It should be easily cleaned from fat stains and stained food evaporation, while showing resistance to chemical cleaning substances.

1. For a soft sofa, the elastic furniture foam from 5 cm thick is used. For semi-chagging - synthetic padding. A thin layer of glue is applied to the back of the sofa in places of pebble or synthesis, and the packing is tightly pressed against the plane of the back.
2. From the upholstery fabric it is cut on the pattern and the size of the upholstery details. The furniture stapler is fastened by the plane of the back from the back side at the seat of the seating and the back. The material is tightly stretched and fixed in angular points. It is then stabilized along the entire length, including the sides.
3. From bar 40x40 mm armrests are made. Over the entire length of the bar, a grocery sample is made in a depth of 20 - 30 mm. The sample width is determined by the side wall thickness. The billet is covered with filler and upholstery. Then the armrests are stamped in grooves glue and sit on the sidewalls. You can additionally fasten the armrests with screws.