How to collect and install the door frame

Much depends on the correct assembly and installing the door frame. Drying and gaps can lead to loosening, jamming or other problems with the door, which will be subsequently difficult to eliminate.

The door frame must be properly adjusted by the door shown, perfectly exhibited in horizontal and vertical levels, as well as firmly fixed in the doorway. In addition, additional sealing is carried out when installing the door frame in order to eliminate drafts and atmospheric influences on the wooden door.

Types of wooden door boxes for home

1. Wooden boxes for door openings are made separately or complete with door cloths - blocks. The parameters of the door box depend on the width and height of the openings and doors. In the width, the doors are divided into single and double.
2. The closed boxes for doors consist of four bars with a spawn made into the correct rectangle. Unlocked - consist of three bars, without a threshold. Such boxes are installed, as a rule, in the internal interroom doorways.

Chemical processing of blanks

1. In order for the box to stoke for a long time, it must be treated with an antiseptic. After drying, the bars are covered in two - three layers of olifa. It is advisable to use a natural olive. It is better preheated, so it absorbs deeper and dry faster. You can apply an ordinary brush.
2. Under the threshold stacked Ruberoid, and better Rubimast in two three layers. If the door is external, then to prevent wood rotting and fungus - a wooden door frame is covered with rubberoid around the perimeter.

Build wooden boxes for doors

1. The height of the side vertical racks along the folded ledge should be equal to the height of the door. Standard door leaf height - 200 mm. Add 2 - 3 mm gap between the bow and the base door.
2. In the event that you are planning a threshold, then on the bottom, add another 3 mm tolerance. Without a clamp, the gap is up to 1 cm, to prevent rubbing in case of precipitation.
3. Door box is collected on the floor in a horizontal position. The attachment of the angles is carried out by the wood screw, and it is better to be furnished with furniture config terms, after their hole diameter. The tolerance for standard installation of confirmates is 2 -3 mm less than the diameter of the screw.
4. In the lying position, the door leaf itself is applied directly to a wooden door frame with shut-off door hinges.
5. On the door frame, the pencil is made fine marking under the clipping loops. The cells under them were crushed by the chisel, but the size and depth of the corresponding thickness of the hinge wing. The second fastener of the loop will be screwed down.

Nuances Fastening Wooden Door Boxes

1. Unlumbed door boxes - must be securely fixed on lags and logs.
2. For this, special grooves are made for properly fastening the door wooden box. Selected nests, are hidden by a decorative board of the velocity function.
3. Usually spikes are nailed to beams or lags with nails, which ensures the stability of a wooden door frame.
4. Wooden door boxes are collected from the gamned bars, which does not allow them to be breached and deformed.
5. Collect door boxes on straight through spikes and glue. There is a different way of fastening the box, for this it is used long screws screwed into pre-torn holes with dowels.
6. Diagonal of wooden box bars provide due durability and rigidity. The lumen _ is dripped by a wet method, that is, cement or gypsum solution, and it is better to blew the mounting foam throughout the perimeter.

Installation of the box in the doorway

1. Install the door frame in the intended opening. The looped side is aligned, but Waterpasus. Mortgage prepared from wooden bars - are adjusted in size and installed on vertical side racks.
2. It is advisable to fly before installing the centered spout bias. Having placed the door frame in the level in the horizontal and vertical plane, you can start the mount.
3. Self-tapping screws in the holes are better to drive not to the end. Putting the box, gradually clamp the self-tapping screws checking the level in all parameters. Self-pressing can be adjusted to the state of the axes.
4. By adjusting the screw screws, the door leaf is hung on the door frame. The regulation continues until the tongues of the latch and bolts of the locks are fully coincided.
5. Recently, construction is very popular with the assembly foam. This is a good method, the foam mass fills all small cracks and has low heat-conductivity.

After drying the foam - the protruding hills are removed by the mounting knife, and the depressions are sealed with a putty mass. In the final, a pen is stuffed with an inner and outdoor side.

At the end of the article there are two videos on how to collect and install a wooden box correctly.