How to make a baby bed do it yourself

Factory cots are quite expensive, and they are purchased for the short period while the child grows. It is possible that the furniture that descended from the conveyor is beautiful and high-quality, but it is massive production and many such models. It is not very difficult to make the original and solid children's bed. To begin with, decide on the size, and purchase the children's orthopedic mattress.

Come up with the model and squeeze the scheme before starting to make a children's bed with your own hands, photos of options and schemes, can be spacked on the Internet. Properly chosen materials and competent assembly will allow you to make a children's bed better and more interesting factory. The unique atmosphere of peace and comfort will appreciate your child and wife. About how to make a children's bed yourself, consider in this article.

Detailing baby bed

1. The mattress is good, orthopedic acquisition in the store. Remember that during the growth period, the child is formed and strengthened the spine and skeleton. Do not save on the health of the child. From the size of the mattress, all subsequent work is planned.
2. The frame is the base of the bed, calculated on the basis of the sizes of the mattress. For its manufacture, a stranded dry board is suitable. Its thickness should be at least 2.5 cm, and the width is not already the thickness of the mattress.
3. The lamellas are a lattice from the Rama listened to the frame or sheet of thick plywood (20 mm) with ventilation holes with a diameter of 40 - 50 mm, installed in the log cabish and supporting the mattress below.
4. Sidewines - fulfill the role of inventive fence. Bottomy varieties are a lot. From the lattice of timber and rails, to continuous from plywood or LDSP.
5. Bylts - in the pack traditionally lower than in the headboard. For them, it is also possible to use LDSP, Phaneur or a woody array.
6. Legs - sometimes there are fragmented and are in the monolithic plane of the sidewall, and often attached separately. They can be bought in the store furniture accessories or make their own from a wooden bar.

Baby skew frame

1. Frame frame for mattress, in fact - wooden rectangular box from boards or boards from laminated chipboard. The width of the board is calculated depending on the thickness of the mattress. Taking into account the mounts for lamellae, the mattress can perform above the upper edge of no more than 5 cm.
2. If the baby cot is made collapsible, then two longitudinal sidewalls of the box, can be fixed on the former. They are hung on special furniture hooks for beds. You can buy them in the store furniture fittings.

Lamella for a mattress baby bed

1. Lamels are designed to support the children's mattress in the frame base of the bed. The frame is measured along the inner perimeter of the frame and is assembled from the bar 3x3 cm. Rama 5 cm wide, 0.5 cm thick and 5 cm with increments of 5 cm.
2. The second option is a plywood 1.5 - 2 cm. In the plywood drill "Feather", 10-20 vent holes are made, with a diameter of 4 - 5 cm and evenly distributed along the plane.
3. On the inner side of the frame of the frame, the fixing bar of 3x3 cm or a metal corner is selected.

Children's bed legs

1. The legs for a crib can be purchased at the store of furniture accessories or make from a wooden bar. The timber will suit 5x5 cm, it can be swollen a little on a trapezium. The legs along the corners of the frame box are mounted, and is fixed through the bolt with a diameter of 8 mm.

Bells and sidewalls for a children's bed

1. Figure fighters and sidewalls are made from the massif of a laminated chipboard or a cohesive board. According to the drawing of a children's bed - the sketch is transferred to a sheet of chipboard and is cut out with an electric jigsaw. If you wish, you can cut curly parts for a baby bed.
2. The sidewalls and the badges from the chipboard are attached to a wooden frame with euroconphirmatics. Corner connections are connected not wooden stud. For this, the holes in the end and conjugate side of the sidewall and the bells are chopped, the stud is labeled with PVA and the plane is joined. For a dense docking, the compound is bubbled with a wooden Cyan.

Children's bed with drawers

1. Practically and convenient to make a children's bed with drawers. In accordance with the drawing, a children's bed with drawers make a frame. Choose for drawers suitable in size and color of facades with handles. They can be cut from LDSP or buy ready.
2. On the sidewalls and the back wall, the board is suitable with a thickness of about 1 cm with a groin feeding for the bottom of the drawer. The bottom is made of fiberboard or thin plywood. The drawer assembled on the confirmates and wooden studs, equipped with the sidewalls guides.
3. There are several types of guides for drawers. Depending on your desire, you can choose roller or sliding guides. You can make primitive guides from the rail or corner, but they are not very comfortable.
4. In the furniture accessory store, it is better to choose a guide for a full pull-out drawer. Equip them with a drawer for a children's bed is not difficult. Guides are disassembled into two parts. A wide plank is attached to the sidewall of the frame box, and the narrow is screwed with small screws to the sidewall of the drawer. Boxes are inserted into place.

Vite to see how to make a drawing of a baby bed of a car and collect it can be seen on the video.