Children's hill do it yourself

The playground at the cottage or in the country house in the garden will be defective without a children's slide. Excessive children's energy aimed at the right track will save nerves parents and give extra time for relaxing outdoors. Interesting plastic collapsible or rubber inflatable children's slides for giving can be purchased in the store. It is not very difficult and not expensive to build a stationary children's slide of wood and metal.

Before starting work on installing a slide, determine the place convenient for it. Children's slide should be firmly and steadily installed and located in a complex with other game facilities - swings, sandbox and a game house. At the end of the descent, equip the landing place. Around this place there should be free space and absent objects that a child can be born. As an option - you can put in the landing place a semi-rigid mat.

Ready inflatable and plastic children's slides

The finished children's slides acquired in the store are designed for age from 1.5 to 10 years. They have a small weight, easily assemble and dismantled. These slides are used, as a rule, in the warm season. Any products for children must be certified.

• Plastic children's slides are made of special high-strength non-toxic plastic, but when buying, pay attention to the maximum allowable weight during its operation. Check for the reliability of assembly fixtures and stability of the children's slide. Metal bolts should be with a rounded smooth surface, and in places to slip down. There should be no sharp corners, hazardous holes or openings in the design, where the hand or leg of a child can get stuck.

• Of the reinforced PVC make bright children's inflatable slides of various formats and configuration. In height, they can reach 5 - 6 meters and have a descent to 8 meters, at the same time up to 10 children can ride such a slide. In the assembled form of its dimensions 1x1x3 meters. There are slides and smaller, you can buy an inflatable slide with a trampoline, a house or a swimming pool. The inflatable slide must be equipped with reliable safety cables and a powerful compressor.

Stationary children's slides of wood and metal

It is not difficult to make a children's slide on their own and not expensive. Such children's slides, whose photos you see on the Internet are made by simple people.

Production of a children's slide of metal

For a metal children's slide, you will need a set of pipes of various diameters from 0.5 to 1 inch, 5x5 cm corner, galvanized sheet, rod, welding, turbochalmic machine, bright oil paints.

1. At the first stage, according to the drawing, weld the framework. The correct square is made of about 1.5x1.5 meters for the top platform and the metal sheet is welded to it not thinner 1 mm. The inner part is strengthened by "x" - with shaped rigids from the same corner. The playground is welded to the support racks. For reference racks, take a pipe with a diameter of at least 1 inches and a length of 3 meters. To the lower ends of the racks weld metal heels - square or round trimming of metal or fittings.
2. In the installed location, dig four pits under the racks of 0.7 - 1 meter. The bottom of the holes rushed with stones and trambed heavy scrap. Install the frame of the children's slide into the pits and align with a plumb and waterpaste. Pans fill with cement mixed with rubble and sink. After hardening the cement mortar, it is possible to continue work on the manufacture of a street children's slide from the metal.
3. Make a "x" - shaped cutting of the frame. From the edge of the site, approximately at an angle of 45 ° welded two corners for the manufacture of steps. The approximate step in height is 20- 25 cm. The transverse staps of steps are welded strictly horizontally, from angle 2 - 3 cm, the plane of the steps can be made from a wooden board. From the pipe ¾ inch is welded with a loss of the triggered, turning into the handrail for the ladder of a children's slide. Fencing and side openings of the handrails of the ladder better tighten with a wire mesh with a shallow cell.
4. For a trigger, you will need two pipes with a cross section. Heat welding or with a pipe bender, two parallel curves are made for the base of the trigger. Initially, the descent must be steep and smoothly switch to the plane approximate to the horizon. The ribs ribs are welded across the curves, and a galvanized leaf is welded with a thickness of 1 mm. Standard galvanized sheet has dimensions: width 710 mm and length 1500 mm. If there is a lack of metal for a solid gutter, it is nachsturing along the sliding. From the half-hearty tube, parallel bottom curves for sides of fence are fired. Approximately 30 cm are welded at a height and sewed from metal residues. From trimming pipes, the support racks for the trigger are welded in three to four places.
5. Metal children's slide is carefully processed by a turbo-shelf machine. They grind all sharp corners and protrusions to full smoothing. A children's slide is painted with ordinary oil or pentaphthalic paint for outdoor metal work. The bottom of the gutter is not painted so as not to slow the slide.

Children's street hill

Of the wood of coniferous rocks make a children's hill with their own hands is absolutely not difficult. To do this, you will need four round logs or square beams with a cross section from 10x10 cm, the timber 50x50 mm, the board 25x150 mm and the galvanized sheet steel for the pitched groove to 1 mm thick.

1. All wooden billets should be thoroughly overwhelmed with electruruck and sandpaper sandpaper. A platform for descent is assembled from the bar and boards, approximately 1x1 meters. The logs or beams are tied with the board and are collected in the frame, on top of which the place is mounted for descent. The compounds are performed using nails and screws from 70 mm long, and in key places are strengthened with a round head bolts and a slot under a screwdriver.
2. If the frame is installed without bass, then it is necessary to provide installation cables - stretching. When you swing up the lower ends of the frame columns by an antiseptic, soak the machine oil or sterolate. Set the level in the holes and pour cement mortar with the rubble.
3. When the cement solution will clarify, start to make the ladder. Two boards 25x150 mm doine under 45 ° C end. And the same boards cut down the steps and secure them with self-draws into the end with a step of 20 cm. On the sides of the steps from the bottom, attach a metal corner or a square rail 20x20 mm. The finished ladder is attached to the supporting beams of the frame in the top of the bolts.
4. From the opposite side there is a scat. Unlike metal and plastic slides, the wooden slide of the skate will be straight. Four - five boards 150 mm wide are oscillate and covered with galvanized steel. Alternatively - can be covered with linoleum. Important: Fasten steel or linoleum is necessarily with the end side of the trigger. From the board is the side side of a height of 300 mm. The chute is exhibited under the angle designed for descent and is strengthened by the support racks from a bar 50x50 mm. Racks are triggered to the height of the side and fixed by bolts and self-draws. At the final stage, it is made from a bar and board of the handrail and the leather fence of the site.

After completion of the joinery, make sure that the slide is completely polished and treated the antiseptic tree. The finished children's slide of wood can be painted in funny colors or open lacquer.