What is electrocamenka. Features and characteristics

To get into the bath or sauna - the procedure is not only a pleasant, but also useful for health. Have your own sauna or bath on the territory of a private house - the dream of many amateurs of the steam. An important choice to be done during the construction of a home sauna is to install a furnace. Do I need to pass a complex procedure for designing a classic furnace on firewood or can I easily facilitate the task by installing a modern electric oven?

Advantages and disadvantages of electrocamen

Electrodenka is an electric furnace model that creates steam. It is also called an electric oven for a bath or just a stone. It is usually a container for stones with built-in ten. The power of the furnace depends on the number of built-in electrical heaters.

Advantages of electrocamers in comparison with wood furnaces are as follows:

• Designing and build a pair without a classic wood furnace is much easier. Mainly because there is no technically complex task for the design of the chimney. This is especially true if the bath must be equipped in one of the rooms at home or an extension, and not a separate room.
• It does not have to invest a lot of strength in the laborious process of wood harvesting; It also disappears the need to build a storage for their stock.
• Electric furnaces for pairs are much simpler and safer to use. Their designs are designed in such a way as to maximize users from random burns. They are equipped with thermostats and fuses to prevent overheating.
• Electrolmen are compact, which will allow you to place them in a small home sauna. For convenience, manufacturers have developed two options for installation - wall and corner.
• If you want to go, you need to make a couple of light actions: turn on the heater, set the desired temperature and that's it. It does not need to spend time and strength on the furnace tolerance.
• Some manufacturers are embedded in Kamenka moisture regulator. Selecting different modes, the steam room will turn into a bath or sauna at will.
• Advanced furnace models equipped with a deferred start. This feature allows you to program the inclusion time so that the coming from the work of the sauna has already warmed up.
• Movers and tanks are made for water heating. Acquisition of such an instance will save on the purchase and installation of a boiler.
• Often electrocamenakes are equipped with a control panel. It is either built into the housing of the furnace, or mounted in a pre-banner.

An essential lack of electrocamery is only one - electricity consumption. Someone else may not have enough sound crackling in the furnace wood and characteristic smell of burning tree. For such samples of bath electric furnaces on firewood.

Types of electrical stoves

Depending on the purpose and functions, the electric shock furnaces on the market are presented in such options:

1. Electrodenka for the sauna (often in a separate category, Finnish electrosenks are isolated).
2. Electrodenka for the Russian bath.
3. Electrodenka for small saunas.
4. Electrocamenka with steam generator.

Models differ not only by functions, but also by and specifications, configuration, materials and design. Together with the furnace, it is possible to purchase accessories and additional items, such as:

• thermal insulation materials
• tEN
• stones
• remote Control,
• steam generator
• power cable.

To buy electrocamers is better in specialized stores or large food hypermarkets. However, the choice is often small. Therefore, the optimal option is to order an electrician via the Internet. Here is always at hand a variety of options. There is time slowly to explore all the technical indicators, materials and characteristics. The most pleasant thing that determined with the model is not necessary to buy it in the only proposed price. After all, competing suppliers offer different prices for the same model. And this is another opportunity to save.

In Russia, in a large assortment, electric ovens for saunas and baths of domestic production are presented. Many and imported models, in particular, from Finland and Sweden are world leaders in the electrician market. Prices vary widely: ranging from 3 000 r. up to 100 000 r.

Good quality furnaces produce such companies as:

• Sawo, Harvia, Tulikivi and Helo from Finland,
• russian Ermak, Polytech, Inzcomcenter VDD, Ural-Mikma-Term,
• and also Tylo (Sweden).

Electrodenka, the price of which is high, will not always be the best option. The selection of the furnace is a process that requires knowledge of some subtleties, which we will talk further.

What should pay attention to when selecting electrical stoves

• It is desirable at the steam design stage, it will be determined with the placement of the furnace. For small rooms, a mounted version of the heater is recommended instead of outdoor. Or choose a compact corner model. Note that for the safe use of the wall electrochannel, the ceiling height should be at least 190 cm.
• Among the various materials of the chassis, the preference is better to give stainless steel. This is the most economical and durable option.
• If the voltage in the power grid is standard, 220 V - the power should not exceed 4.5 kW.
• More powerful furnace models require rated voltage in a network of at least 380 V.

• The calculation of the required power is made according to the following formula. If the room is a steam room less than 10 m ³, then each cubic meter of the square should have 1 kW of power. If the room is more, the coefficient is 0.8 kW per m ³. At the same time, the steam room should be well insulated, and the ventilation system is established according to the current construction standards.
• Ventilation system, when installing a furnace with a steam generator, special attention should be paid.
• Provide the ability to create grounding to install the electrical machine.

Electrocamena for sauna or bath

To begin with, we define the main differences between the bath and sauna:

1. The temperature in the sauna is higher than in the bath. And moisture, on the contrary - in the bath is higher. Therefore, the sauna is usually transferred to the body easier, although the wet pairs of the bath is considered more effective for recovery.
2. For the sauna, the presence of the pool is necessary, whereas in the bath it may not be. It is also associated with air humidity.
3. In the sauna, in contrast to the bath, the stones lie openly.
4. Double brooms are used only in the bath; In the sauna, they quickly dry and shrink.

Armed with these knowledge, electrocamers produced separate models for the sauna, and separate - for the bath. When choosing one of them, consider the following:

1. Samples for saunas create a dry pairs, and for baths, respectively, wet. The latter can be additionally equipped with a steam generator.
2. In the bath should not be open fire. Bath models of electrocamers are made with a closed stove, inside which stones are split. They produce both gas electrodelocks for a bath and more traditional - wood.
3. Furnaces with steam are considered less fire-hazardous, since dry air can lead to overheating of a wooden trim. At the same time, modern models of the sauna furnaces maximally meet all fire safety rules.
4. Finnish electricians are characterized by environmental friendliness, high quality materials and beautiful design.
5. Stones in the electric furnace pick natural. It is better not to experiment with this in order not to harm health.

A few words about stones for baths and saunas

1. Stones in the electric furnace pick natural. It is better not to experiment with this in order not to harm health.
2. It should be immediately abandoned from granite and marble, as they are mined in places with an increased radiation background. As a rule, the indicators are not significant, but with regular use, irradiation is inevitable.
3. Before laying in the oven, stones need to rinse with water and dry in air.
4. Small stones should be selected. Of the remaining the largest places on the bottom of the electrocamenki.
5. Heating elements (tanes) should be closed with stones.
6. Make it then so that the stones in the furnace were enough. Otherwise, the steam room will be too quickly warm up that again it is bad to affect well-being. However, if the stones are too much, the circulation of air between them will slow down, and at the same time the process of heating the room will be delayed.
7. Facing the furnace is best done from natural stone. Stones are sold as packages and for a swim. Price from 8 r. up to 300 p. per kilogram. The most common for use in electrocamenakers are such rocks of natural stones as:

• diabases - environmentally friendly mining of black breed. One of the most typical stones for saunas and baths, including due to its low cost. It has a high heat capacity and density, racks to wear, durable and durable;
• serpentinite tangled has excellent heat accumulating properties. It is believed that this breed has a therapeutic effect and is especially useful for people with diseases of the respiratory tract. Also serpentinite attracts many with its aesthetic species;
• talco chlorite - rock formation formed from natural minerals. It accumulates well and evenly gives warmth. Racks to the effects of high temperatures, has increased heat capacity and durability;
• quartzite Raspberry - natural, natural stone with quartz mineral composition. It has a characteristic raspberry shade, which gives him special beauty. Environmentally friendly, durable and durable, has a low thermal conductivity. It is also believed to have therapeutic properties.