Banquette your own hands

The wooden banquette is a stylish and practical accessory for any room. It is quite spacious, so it can be used to store the necessary things. Most often set the banquettes to the hallway, they perform not only the function of the chest, but also serve as a convenient place for seating. This subject of the interior due to the simplicity of its design is quite possible to do on its own. For this, there will be no time consuming and forces. About possible ways to make a banquette with your own hands, let's tell me further.

Banquette from the old table

This banquette is fully accomplished and quite quickly. This requires the presence of some materials:

1. Porolon 5-6 cm thick.
2. Fat couch wool.
3. Plywood sheet 1.5 cm thick.
4. Aerosol glue.
5. Fabric for plating.
6. Building stapler (better electric).
7. Sander.
8. A serrated knife, hammer, screwdriver.
9. Primer, paint.

In addition, we need an old coffee table of any shape and size. For example, such as in the photo:

Stages of performance:

• In order to upgrade the old coffee table and turn it into a new banquette, initially you should unscrew the locking screws, and remove the top cover from it. It follows this as shown in the photo.

• Now go to the processing of the upper part of the future banquette. To do this, we take a sheet of plywood with a thickness of 1.5 cm and attach a 5-6 foam plate to it. 5-6 cm. The dimensions of the foam rubber sheet should be 1-2 cm more than that of plywood. Cut the pieces of material of the desired size using a serrated knife.
• Cutting watts. It should be done by 5-6 cm longer and wider than the reservoir of the foam rubber. This is necessary in order to be the possibility of the remaining edges of the material to wrap the countertop.
• We cut the casing fabric. The size of the material must be 5-6 cm more so that there was an opportunity to wrap the edge of the plywood and foam rubber sheet.
• We fasten all the layers of the upper part of the banquette. Initially, there is a plywood, foam rubber put on it, then cotton. Next, all turn on the trim cloth. All parts are bonded with the help of aerosol glue. After that, give the layers of the material for some time to dry.

• Tissue cloth All parts of the design should be covered quite tight. Then capture the material on the back of the table top with the help of construction brackets. Particularly attentive should be when processing the corners of the structure. So that they get smooth and straight to fix cloth use 2-3 brackets per angle.
• Now we go to the processing of the bottom of the bedside banquet. To do this, carefully grind the old coffee table without a tabletop. To do this, use a manual grinding machine with a grain of 120 and a sheet of sandpaper. Pretty grinding both legs and side surfaces of the design.
• Next, the lower part of the polished frame should be projected. This requires any machine-based primer material. After that, let's give a mixture to dry.
• Then paint the frame. You can use aerosol paint of any color. That the coating was monochromatic and uniform, apply the paint in 2-3 layers. That's all, the bedroom for the bedroom is ready.

How to make a banquette of girlfriend

To do this, we need:

1. Bruks plywood for the construction of the bottom of the structure - 6-8 pcs.
2. Plywood sheet (MDF) 6-7 cm thick.
3. Faro Foofer.
4. Building stapler (better electric).
5. Wool.
6. Drill.
7. Self-tapping screws (size 3 cm).
8. Glue.
9. Hammer, screwdriver.
10. Upholstery buttons.
11. Needles and threads.
12. Fabric for plating.

Stages of performance:

• Cut a sheet of MDF to the size of the banquette you need (its top). Next, there is a pencil, we note the place where screws will be placed (usually 8-10 marks are required). After that, on the markup made, we turn the hole drill. Fix the bar on top of cement-contact.
• Top on the MDF leaf fix the reservoir of the foam rubber. Material can be bought in any economic or construction store. We lay the wool layer on top (as described in the first method of assembling the banquette). Fix it to the base with the help of a furniture stapler. Carefully cut the surplus.
• On the bed layer we put the casing fabric. If it has a drawing, before cutting the material, check that it is exactly in the middle. I fix the cloth with brackets on the reverse side.
• Pretty tensioning fabric at the corners and fix it with 3-4 brackets.

• You can decorate the top of the banquette using ordinary buttons that you can buy in any economic store. It is also allowed to use conventional buttons for this. So, initially, we denote 7 points where buttons will be located (buttons). Next, wrapped the buttons (or buttons) with a cloth, sew them to the upholstery. We do this as shown in the photo. In order for a carriage screed look more attractive, thoroughly align their fingers each folding material and stroke her iron.

• Now we collect the bottom of the dressing room for the living room. For this, we will need several bars: 6 pieces 2x2 with a height of 40 cm (for legs), 6 pieces 2x2 (for jumpers). Grind, soil and paint the available boards. Next, we install in the right places the bars-legs of the structure and fasten them with each other with jumpers. Place the legs and side parts of the design follows as shown in the photo.

• Connect the design into a single whole. For fixation, screws and liquid nails will be required. Thus, we have a beautiful and functional banquette of girlfriend.

Bannament: Photo

Banquette in the form of an open sofa

For manufacture, the following tools and materials will be required:

1. Board or furniture shield with a thickness of 20-26 mm. (If the board is used, it will take pre-processing of the material, grinding, coating with protective compositions).
2. Furniture mounting tape.
3. Furniture pins.
4. Porolon (or other soft filler).
5. Screws, self-tapping screws (size 3 cm).
6. Drill.
7. Carpentry glue.
8. Electric jigsaw.
9. Screwdriver of low power.
10. Hammer, screwdriver.
11. Machine for grinding.

Stages of performance:

1. The size of the banquette can be absolutely any. Based on this, you can adjust the dimensions of building materials (boards, furniture shield, wooden bars). Therefore, picking up a suitable place to accommodate a banquette, make it measurements and schematically display the drawing of the future design.
2. The banquette will consist of several cubes, each of which has two side walls, a lid, bottom and rear wall. Due to the fact that in the design there will be no front walls, the obtained niches can be used as storage cells (clothing, bedroom accessories, etc.).
3. Perform markup on the board (furniture shield) according to the existing drawing. Now cut the appropriate parts of the design. This will require an electric lobby. Please note that the upper lids of the banquette will be fixed on top of the side walls, and the bottom and the rear panel will be located at the bottom of the structure. If the product consists of 3-cubes, then you will need 6 parts to assemble lateral walls, as well as 3 parts for the bottom and rear panels. It is worth saying that the banquette with a back is made according to such a scheme.
4. After all the necessary details are cut, you should polish them well. This will require a manual grinding machine and sandpaper.
5. Next, we combine the resulting parts of the design with furniture pins. To do this, initially drill holes in the ends of the desired size.
6. After assembling the design, we process the joints of the joints with joinery glue. In order to ensure a more reliable fixation of the design, you can fix it with self-reasons. Now we have got the collected 3 cubes, which will be a frame of the banquette. The resulting boxes are collecting together. For fastening, you can use screws, self-stakes.
7. We process the design with protective compounds, soil and cover paint. We give time to the frame back.
8. Next, go to the manufacture of the upper part of the product. The seat for the seat can be covered with an old mattress, cut in size. In addition, for this purpose you can use Faofor Plast. For the selected filler you need to sew a protective case.
9. After that, fasten all parts of the product into a single design. For this, you can use construction brackets. Now our banquette is ready for use.